Star-water-systems HSP20P1 Bedienungsanleitung

LAWN SPRINKLER, IRRIGATION PUMPMODEL # HSP10P1, HSP15P1, HSP20P1Questions, problems, missing parts? Before returning to your retailer, call our custom

10PUMP PREPARATION FOR WELL AND SURFACE WATER13. Install well seal (not included) in order to hold the inlet pipe in position in the well. 14. Glue a

11PUMP PREPARATION FOR WELL AND SURFACE WATERPUMP INSTALLATION FOR WELL AND SURFACE WATER1. Mount pump on a solid foundation as close to the water s

12PUMP INSTALLATION FOR WELL AND SURFACE WATER3. Connect the 2 in. union together to complete the inlet line to the pump.4. Glue a 6 in. piece of 1-

13PUMP INSTALLATION FOR WELL AND SURFACE WATER6. Connect the 1-1/2 in. outlet pipe to the sprinkler system (not included) by gluing in additional sec

14PUMP ELECTRICAL INSTRUCTIONS Wire Size ChartDistance From Motor To Fuse Box, Meter or Electrical OutletMinimum Copper Wire Size Chart (Gauge)Single

15PUMP ELECTRICAL INSTRUCTIONSA BL2L1IL1271A BL2L1IL1272232. Thread electric wire strain relief (not included) into wire opening on the side of the m

16A BL2L1IL12734PUMP ELECTRICAL INSTRUCTIONS4. Connect white power lead to L1 and black power lead to L2.5. Connect green ground wire to green groun

17PUMP ELECTRICAL INSTRUCTIONSb. Pull the red wire with the female flag connector from the “B” terminal. Place it to the right on the L2 terminal spa

18PUMP PRIMING AND STARTUPIL1278Priming Plugwith PressureGaugeOutlet PipeInletPipeAir Relief PlugIL1279Priming Plug with Pressure GaugeAir R

19PUMP PRIMING AND STARTUPIL1288Priming Plug with Pressure GaugeWater LevelPipe TeeClosedOpen565. Wait 10 minutes to see if water level drop

2 SAFETY INFORMATIONPlease read and understand this entire manual before attempting to assemble, operate or install the product. • NOTE: Pumps with

20 IMPORTANT: If the pump fails to prime within five minutes:7. Turn the power off at the break box. Check all pipe connections for leaks, making s

21TROUBLESHOOTINGProblem Possible Cause Corrective ActionA. Little or no discharge1. Casing not initially filled with water 1. Fill pump casing2. Ve

22CARE AND MAINTENANCEWinterizing CAUTION: Drain the entire system if there is danger of freezing. A drain plug is provided at the bottom of pump fo

3Before beginning installation of product, make sure all parts are present. Compare parts with package contents drawing. If any part is missing or dam

4GENERAL PUMP INFORMATIONTypical Pump SetupTypical setups for lawn sprinkler pump systems include ground water wells (Fig. 1) or surface water, such a

5Vertical LiftVertical lift is the vertical distance from the lowest level of the water to the pump intake. The pump will move water as long as the pu

6PUMP PREPARATION FOR WELL AND SURFACE WATERIL1252IL1253IL12541. Thread 1-1/2 in. MPT x 1-1/2 in. slip adaptor (not included) into the outlet port lo

7PUMP PREPARATION FOR WELL AND SURFACE WATER4564. Glue a 1-1/2 in. slip x 1-1/4 in. adaptor (not included) to the top opening of the 1-1/2 in. tee. 5

8PUMP PREPARATION FOR WELL AND SURFACE WATER7. Glue the male thread side of a 1-1/2 in. union (not included) to the pipe.8. Thread 2 in. MPT x 2 in.

9PUMP PREPARATION FOR WELL AND SURFACE WATER10. Glue one side of a 2 in. union (not included) to the pipe.For Well Installations11. Thread a 2 in. MPT